Suppressing *W* messages in PDL

[Joe Boyle]

Could it not be replaced by entering a blank line at the appropriate record
number in one of the designer message files ?

Regards, Joe.

This e-mail and all information contained in it is confidential and may be
legally privileged. If you are not the intended recipient, your access to
this e-mail is unauthorized. Any use, dissemination, distribution,
publication or copying by you of this e-mail or any of the information
contained within it is prohibited and may be unlawful. Do not open any
attachments, delete it immediately from your system and notify the sender
promptly by e-mail that you have done so. The content of this 
e-mail and any attachments sent with it may have been altered without the
consent or knowledge of the author.

-----Original Message-----
From: powerh-l-admin@lists.sowder.com
[mailto:powerh-l-admin@lists.sowder.com] On Behalf Of Deskin, Bob
Sent: 17 November 2004 14:16
To: PowerHouse Mail List (E-mail)
Subject: RE: Suppressing *W* messages in PDL

If I understand the question, Robert wanted to suppress that specific
message. There's no way to suppress a specific warning message unless
you actually correct the cause of the warning.

As an alternative, you could output the listing to a file and analyze
that file in a text editor that allowed you to look for warnings not
matching that one.

Bob Deskin              
Senior Product Manager, Application Development Tools, Cognos Inc.
bob.deskin@cognos.com (613) 738-1338 ext 7268 FAX: (613) 727-1178
3755 Riverside Drive P.O. Box 9707 Stn. T, Ottawa ON K1G 4K9 CANADA

-----Original Message-----
From: powerh-l-admin@lists.sowder.com
[mailto:powerh-l-admin@lists.sowder.com] On Behalf Of Johnson, Tracy
Sent: November 17, 2004 8:59 AM
To: PowerHouse Mail List (E-mail)
Subject: RE: Suppressing *W* messages in PDL
Importance: Low


Robert Mills asks:
> 
> Greetings to the list,
> 
> Environment: MPE/iX 6.5 running PowerHouse 8.19.D7, 8.39.C and 8.49.D
> 
> When I compile my dictionaries I'm getting over 400 of the
> following warning messages:
> 
>   *W* The storage type and size may be too small for some values.
> 
> Is there any way to suppress this message as we find
> important warning, that should be looked at, are lost in the 
> amount of output.
> 
> regards,
>  
> Robert W.Mills

The command is ancient in Powerhouse, goes all the way back as far as I
know:

SET NOWARNINGS

(Never tried the short version of "SET NOW" but I guess that would work
too.  It seemed too ambiguous.)

BT


Tracy Johnson
MSI Schaevitz Sensors 

= = = = = = = = = = = = = = = = = = = = = = = = = = = =
Mailing list: powerh-l@lists.sowder.com
Subscribe: "subscribe" in message body to
powerh-l-request@lists.sowder.com
Unsubscribe: "unsubscribe <password>" in message body to
powerh-l-request@lists.sowder.com
http://lists.sowder.com/mailman/listinfo/powerh-l
This list is closed, thus to post to the list you must be a subscriber. 
  
       This message may contain privileged and/or confidential information.
If you have received this e-mail in error or are not the intended recipient,
you may not use, copy, disseminate or distribute it; do not open any
attachments, delete it immediately from your system and notify the sender
promptly by e-mail that you have done so.  Thank you. 
 

= = = = = = = = = = = = = = = = = = = = = = = = = = = =
Mailing list: powerh-l@lists.sowder.com
Subscribe: "subscribe" in message body to powerh-l-request@lists.sowder.com
Unsubscribe: "unsubscribe <password>" in message body to
powerh-l-request@lists.sowder.com
http://lists.sowder.com/mailman/listinfo/powerh-l
This list is closed, thus to post to the list you must be a subscriber.